Glossy Clear Coat
D320 is a premium, GLOSS, extremely durable, waterborne, clear coating.
D320 is a premium, GLOSS, extremely durable, waterborne, clear coating.
D320 is a premium, extremely durable, waterborne, clear coating.
Containing both ultraviolet absorbers and hindered amine light stabilizers for the maximum in UV light protection.
ClearFlex™ ME is a fourth generation product formulated to protect digitally produced images that have been applied to flexible vinyl to "pop" color development, waterproof and seal, and to provide ultraviolet light and abrasion resistance.
Our customers, Our biggest value.
Thanks to them we continue to improve our products.
UV inhibiting--Long lasting
Good abrasion resistance
Chemical resistant to gasoline, oils, diesel fuel, and detergent.
RF weldable
Non-yellowing
Fast dry*, low odor
Flexible
Very resistant to water exposure
Easy water cleanup
Low VOC
DOT nonhazardous
We provide the right ink set according to many different printers colors configuration. Our Process colors are based on a Clean Yellow shade and slighty violet magenta, this combination provides vibrant colors and unbeatable reds.
The most commonly used method of measuring light fastness of a printed material is to expose it to a special artificial light with a spectrum similar to the sun light. Material sample will be exposed together with a special wool counter-sample printed with 8 grades of Blue dye (Blue Wool Scale).
The Swiss Federal Department of Home Affairs (DFI) adopted in March 2008 an amendment to the Ordinance of 23 November 2005 on Materials and Objects in Contact with Food (SR 817.023.21). It entered into force on 4 January 2010 and lays down the obligation for packaging inks to be manufactured only with the authorized substances. Permitted substances are defined as those listed in Annex 2 Lists I and II and in Annex 10, December 2020.
The lists in the Ordinance simply states that the substances may be used in the manufacture of printing inks. To ensure safety in accordance with the law, the migration limits for substances must not be exceeded for final packaging. Guides of Good Practice for the manufacture and printing of printing inks should be followed.
Substances listed with status 'B' may be used, provided that the final packaging is in compliance with the requirements of the Ordinance, i.e. the migration of the listed substances cannot be detected using a valid and official analytical method. The migration should not be greater than 0.01 mg / kg (10 ppb).
INX carried out a review of the raw materials used in the products below to determine their status with respect to the Swiss Ordinance and found that the products below meet the Swiss Ordinance Annex 10.
Accordingly, it does not automatically mean that the product or substance is toxicologically suitable to be used for printing inks for all types of food packaging.
Our products provides the best perfomances required by different applications and markets. Discover how many applications you could cover with this product.
COVERAGE: [average]
Theoretical at 1/2 mil DFT: 1010 sqft/gal
Theoretical at 1 mil DFT: 505 sqft/gal
Recommended min. DFT: 1 mil
SURFACE PREPARATION
Clean surface thoroughly of foreign contaminants. Vinyl: apply one or two coats to provide
THINNING:
This is a water soluble product. Thinning is not recommended as it will reduce the effectiveness of the product.
Hand Application:
Use a 1/4 inch close nap roller for the best performance on large surfaces. For small pictorial areas or digital prints, brushing is better using a 4 inch foam brush or foam paint pad.
Always load the applicator with the maximum amount of coating as possible and apply with light pressure. This will prevent bubbling. Vigorous rolling and high pressure may produce a frothy surface.
Spray Application: Do not use Wagner or airless spray equipment. This type of equipment puts too much material on the surface.
Use conventional air atomization equipment. Fluid tip size should be 0.045” - 0.060” at 30 pounds atomizing pressure at 9 - 12 cfm.
Automatic Application:
For automatic application using the Seal AquaSeal 1600 or 3200 series reservoir 3/4 full and 0-10% water to reduce.
Using more water will result in thinner laminate and less protection. Remember, at 10% reduction with one pass
For full protection use D320 unthinned and apply two more coats.
UV PERFORMANCE
Test results show that a one mil (0.001 applied in two applications of 0.5 mil each, blocks >90% transmission of ultraviolet light.
LIMITATIONS: ALWAYS TEST BEFORE USE!
Do not apply to murals that have been applied to walls or any surface that is subject to water absorption or negative hydrostatic pressure. Do not apply
stored in high humid temperatures. This coating may crack or delaminate on high gloss blackout vinyl when the vinyl is aggressively seam sown. Not for use on NON-waterproof paper substrates.
CLEANUP SOLVENT:
Water or MEK (methyl ethyl ketone) for dried spots.
Our commitment is to provide the most common and used packaging's types available. Find the package that fits your needs.
Read more about this product, you will find useful info and technical details about it, as theTemperature exposure and Jetting, Storage conditions, Shelf Life, and more.
D320 is a premium, extremely durable, waterborne, clear coating.
Containing both ultraviolet absorbers and hindered amine light stabilizers for the maximum in UV light protection.
ClearFlex™ ME is a fourth generation product formulated to protect digitally produced images that have been applied to flexible vinyl to "pop" color development, waterproof and seal, and to provide ultraviolet light and abrasion resistance.
Solvent, low viscosity, pigmented ink set formulated for use in Seiko®, Dimatix®, Ricoh® and Konica Minolta® Heads.
INX Digital’s VSM ink is a premium True Solvent high density pigmented ink set formulated for use in PH with 35 - 120 picoliter drop size.
INX Digital’s MS8 ink is a mild solvent, low viscosity, pigmented ink set formulated for use in PH with 5-50 picoliter drop size.
INX Digital’s PNX ink is a low viscosity mild solvent pigmented ink set formulated for use in PH with 15-35 picoliter drop size.
Low-Cost solvent-based inks optimized for printers using Epson® printheads with 3-15 picoliter drop size.
Premium ECO solvent inks for use in printers utilizing Seiko®, Ricoh® and Konica Minolta® printheads technology.
